The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
Comparative industry trade benchmarks-APP, download it now, new users will receive a novice gift pack.
The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
How to align trade data with ERP systems
author: 2024-12-24 00:33HS code referencing for port authorities
author: 2024-12-23 23:49Dynamic duty drawback calculations
author: 2024-12-23 23:38USA customs data analysis services
author: 2024-12-23 22:55Predictive trade infrastructure analysis
author: 2024-12-23 22:32Data-driven trade invoice verification
author: 2024-12-23 23:49Global trade analysis dashboard
author: 2024-12-23 23:48Country-specific HS code exemptions
author: 2024-12-23 23:25Timber (HS code ) import patterns
author: 2024-12-23 23:00662.56MB
Check795.35MB
Check625.31MB
Check451.66MB
Check831.71MB
Check987.48MB
Check843.21MB
Check814.42MB
Check942.82MB
Check928.95MB
Check174.85MB
Check622.53MB
Check444.65MB
Check242.94MB
Check599.86MB
Check623.93MB
Check719.55MB
Check787.33MB
Check968.84MB
Check578.76MB
Check417.84MB
Check128.21MB
Check312.83MB
Check899.36MB
Check875.68MB
Check757.85MB
Check915.82MB
Check786.69MB
Check372.77MB
Check629.59MB
Check833.73MB
Check865.16MB
Check718.89MB
Check581.25MB
Check431.83MB
Check776.73MB
CheckScan to install
Comparative industry trade benchmarks to discover more
Netizen comments More
1042 Real-time supply chain event updates
2024-12-23 23:52 recommend
977 HS code-based quality control checks
2024-12-23 23:27 recommend
969 Global trade news aggregation
2024-12-23 23:00 recommend
630 Supply chain optimization with trade data
2024-12-23 22:41 recommend
465 Ceramic tiles HS code classification
2024-12-23 22:30 recommend