Organic cotton HS code verification

List of contents of this article:

• 1,Organic cotton HS code verification The difference between Fanake system mf and mfplus
• 2, What do camera af and mf mean
• 3, Fanake MF system F-value parameter
• 4. Frank 0i-mf system how to choose computer transmission program
• 5, How to turn off the spindle detection function of Frank mf system

The difference between mf and mfplus

different functions and different application scenarios. MF Plus is more advanced than MF, with higher performance and stronger functions.Mf is a simplified version of 0i-MD. The main difference is that the control axis mate is 3-axis and MD is four-axis. There is also a high-speed processing function in terms of control mode.

CNC system. It can meet the processing of titanium alloy, cast iron, steel, aluminum, mold steel and other materials. It is used for high-efficiency, high-precision, automatic continuous cutting of complex-shaped surface parts, especially suitable for mold production and processing.

The difference between fanuciseries and mf is that they are different in brand, architecture, application field and programmability, as follows: Brand: Fanuc series belongs to Fanuc, while MF series belongs to Mitsubishi Electric.

MK350N PLUS has more functions than MF250N, MK350N plusThere are functions such as illumination, color temperature, color rendering index (R1-R15), spectrum chart, trobe, TLCI CQS TM-30, etc. There is also software that can be connected to the computer, or download the mobile phone APP to connect to the mobile phone. The hardware has touch screen and charging functions.

Fanake mfplus can receive Heidehan grating ruler. According to relevant public inquiries: Heidehan grating ruler is divided into two categories: open and closed. Among them, the open is high-precision, and the output waveform is sine wave. It is mainly used for the digital transformation of precision instruments, and the highest resolution can reach 0.1μm.

Z+O.T usually indicates that the Z-axis positive overload protection is triggered on Fanaco's equipment. This is usually caused by the fact that the Z axis exceeds its rated load or exceeds the operating specifications.

What do camera af and mf mean

The body sets the camera autofocus/manual focus switch of AF/MF. AF means that the autofocus function of the camera has been turned on. Of course, this also needs to be matched with the autofocus lens. MF indicates the driving power supply of the camera's high-magnification autofocus motor. Even if the camera is installed with a lens with a focus motor, it cannot autofocus.

In the camera, AF and MF are focus modes, that is, autofocus and manual focus. AF, also known as Auto Focus, is autofocus, is the camera that automatically finds a clear focus when shooting, and then automatically adjusts the focal length of the lens to make the photographed object clearly visible.

AF stands for autofocus and MF stands for manual focus.The meaning of AF: It is to use the principle of object light reflection to accept the reflected light by the sensor CCD on the camera. Through computer processing, the method of driving the electric focusing device to focus is called automatic focusing.

AF on the lens means autofocus, MF means manual focus, and AF/MF means automatic and manual switching. Mainly when taking photos, camera manufacturers provide different focus options according to the usage habits of different people. AF stands for autofocus, and the camera automatically controls the lens to focus.

AF/MF on the lens means the switch between automatic and manual, mainly when taking photos, whether the photographer is used to manual focus or autofocus. AF stands for autofocus, and the camera automatically controls the lens to focus. MF stands for manual focus, that is, the user stwes the focus ring through his own feeling.

Fanaco MF system F-value parameter

The parameter setting is as follows: 0012/0MIRx Axis mirror settings : 0 off, 1 on. The movement distance of the 0012/4AIC axis command: 0 is according to the specified address, and 1 is the incremental command. 0012/7RMVx controlled axis removal setting: 0 do not remove the controlled shaft, 1 remove the controlled shaft.

The system parameter 3299#0 PKY is set to 1, and the setting screen cannot be set [write parameter]. It must be set through the signal G40.

fanuc Parameters: 502: radius r; 503: starting angle α; 504: number of holes n, when n0, processing counterclockwise, when n0, processing clockwise; 505: hole bottom Z coordinate value; 506: R plane Z coordinate value; 507: F feed Quantity.

How to select the program of computer transmission in Frank 0i-mf system

Frank md system uses software transmission tool to transfer program method: set computer attributes, local connection-right-click- Attribute-Protocol Version 4-Attribute, set the IP address.Set the IP address of the machine tool and test PING the communication. Or the communication setting test program on the software is used by the transmission software.

First, find the directory function key on the screen operation table, and then click the operation to enter. Then you will enter the next-level function key and click the device. Then you will enter the next level, turn the page to find "USB" and click it. Then turn the page again, find the "Select" button, and click to enter.

Set the machine tool parameter No. 20 to 4 and change the order of the parameters as follows: enable the parameters to be turned on. In the MDI method, press the OFFSET SETTING key, find the setting, and write the parameter to 1. At this time, there will be a No. 100 alarm, and press RESET and CAN to clear at the same time. The I/O channel is 42 to write the parameter to 0.

, the steps are as follows: press (operation), F to read. Enter 01 and press F to set. Enter 1111 and press O to set. Press Execute, and the program will be copied into the machine tool.

There are generally two ways to transfer the .nc file on the computer to the processing center of the Frank System (FANUC Series Oi-MD): card transmission and wire transmission. Card transmission is to directly copy the .nc file to the memory card dedicated to the machining center and then plug it into the machine tool through the card reader.

Install FTP or TFTP server software on the computer and upload the program files that need to be transferred to the server. In the operation interface of Franklin CNC system, select FTP or TFTP protocol, enter the server address, user name, password and other information, and connect to the server.

How to turn off the spindle detection function of the Frankish mf system

1. The steps for the Frank CNC lathe to set the spindle load alarm in a certain program are as follows: open the control interface of the CNC lathe and enter Relevant settings menu. The specific steps will vary depending on the CNC system. Please refer to the operation manual of the CNC lathe. In the relevant settings menu, find the spindle load alarm setting option.

2. First, turn on the spindle after power-on. For example: M3S500, and then execute M19 to check whether the diagnostic 445 parameter has changed. If the diagnostic parameter 445 has always been 0, check whether the NC parameter 3117#1 is 1. Then press the reset button.After pressing the key, the diagnostic parameter 445 becomes 0, and check whether the NC parameter 4016#7 is 0.

3. RESET (reset key): Press this key to reset the CNC system. Including canceling the alarm, spindle obstacle reset, midway exit automatic operation cycle and midway exit input, output process, etc. 2. CURSOR (CURSOR MOVE KEY): MOVE THE CURSOR TO THE EDITING PART.

4. The method of stopping the spindle is: first, after the spindle rotates in the MDI state, press the manual key and the indicator light turns on. Then press the spindle stop key, and then enter M0M30 or M02 at the end of the program, and finally the spindle stop shutdown can be completed.

5. The solution is as follows. Find the PLC switch software under the normal page, press the Y key, and then pressThe next setting is valid, move the cursor to items 30 and 31, press the ON key, and the handwheel moves the Z axis to the stroke. Press: OFF button to close: 30, 31 items, confirm each knife number. M01 is to choose xing parking.