. Check that the exhaust pipe is not smooth. If it doesn't work, clean or replace it. Drive for a while to check whether the oil is missing and whether the exhaust pipe is still injecting oil. Measure the cylinder pressure, and the cylinder pressure is normal: that should be the burning oil caused by the aging and damage of the valve oil seal, and replace the valve oil seal. It is recommended to replace all oil seals.
If there is an oil leak, we should immediately contact a professional technician for repair. Once we find the problem of engine oil, we need to carry out careful inspection and repair. First of all, we can check whether there is any leakage of the oil filter. If so, we need to replace the oil filter.
Possible reasons: the cylinder, piston and piston ring wear exceeds the limit, or the piston ring is opposite, the piston ring is broken, the cylinder is pulled, the cylinder leaks into the crankcase, and the oil is blown out; the oil is added too much, the oil is stirred and discharged;... It is recommended to investigate and solve it from shallow to deep.
If it's just a drop of oil, the engine power performance can still guarantee normal operation, so it's not a serious problem.
The newly overhauled engine has some cases of burning lubricating oil, whichIt's normal. As long as you avoid the four taboos and often check the height of the coolant and lubricant, there should be no big problem.
Don't wait until there is a breakdown to pay attention to it. The consequences can be unimaginable. Secondly, it may also be because the valve rod and the valve duct are seriously worn, or the sealing is too poor, resulting in too large a gap, resulting in the situation of oil, which needs to be repaired in time.
1. Check whether the engine cylinder pressure is normal and whether there is air leakage. Clean the oil circuit, replace the spark plugs, filters, etc. Check whether the four wheels are dragging brakes.Check whether the quality of the oil is good. If not, replace the new oil.
2. Insufficient oil supply. The fuel system should be able to spray well-atomized fuel into the cylinder in a timely and appropriate amount. If the fuel system fails and the amount of oil in the injector cylinder is small, the heat generated by combustion is reduced. When the heat is reduced to the point that it cannot meet the requirements of the engine load, the engine is weak.
3. The reasons for Chaiwei's engine's boring hill climbing are as follows: excessive carbon accumulation: it is recommended to check whether the engine has accumulated too much carbon, which may generally lead to excessive carbon accumulation. Insufficient oil supply: The fuel system should be able to inject atomized fuel into the cylinder in a timely and appropriate manner.
1. Improper maintenance: The correct method is not mastered during maintenance, and low-purity gasoline or fuel oil is used, which will cause damage to the Weichai Guoliu natural gas egr valve. It is necessary to maintain the EGR valve regularly, clean up the accumulated carbon, and use gasoline and fuel additives with the correct label.
2. Engine jitter and lack of cylinder. Common reasons include spark plug ignition failure, ignition coil leakage, internal short circuit of the electric coil causing intermittent non-jump. The rust of the engine exhaust pipe causes the exhaust pipe to make a poof, and the exhaust gas is discharged from the middle without passing through the exhaust pipe, resulting in abnormal engine noise.
3. Simply put, the engine is an energy conversion mechanism, that is, the thermal energy of gasoline (diesel) is converted into mechanical energy through dense, which is the most basic principle of the engine.
4. Check whether there is too little fuel in the fuel tank and whether the pressure in the fuel pipe is unstable.
Industry-wise trade data breakdowns-APP, download it now, new users will receive a novice gift pack.
. Check that the exhaust pipe is not smooth. If it doesn't work, clean or replace it. Drive for a while to check whether the oil is missing and whether the exhaust pipe is still injecting oil. Measure the cylinder pressure, and the cylinder pressure is normal: that should be the burning oil caused by the aging and damage of the valve oil seal, and replace the valve oil seal. It is recommended to replace all oil seals.
If there is an oil leak, we should immediately contact a professional technician for repair. Once we find the problem of engine oil, we need to carry out careful inspection and repair. First of all, we can check whether there is any leakage of the oil filter. If so, we need to replace the oil filter.
Possible reasons: the cylinder, piston and piston ring wear exceeds the limit, or the piston ring is opposite, the piston ring is broken, the cylinder is pulled, the cylinder leaks into the crankcase, and the oil is blown out; the oil is added too much, the oil is stirred and discharged;... It is recommended to investigate and solve it from shallow to deep.
If it's just a drop of oil, the engine power performance can still guarantee normal operation, so it's not a serious problem.
The newly overhauled engine has some cases of burning lubricating oil, whichIt's normal. As long as you avoid the four taboos and often check the height of the coolant and lubricant, there should be no big problem.
Don't wait until there is a breakdown to pay attention to it. The consequences can be unimaginable. Secondly, it may also be because the valve rod and the valve duct are seriously worn, or the sealing is too poor, resulting in too large a gap, resulting in the situation of oil, which needs to be repaired in time.
1. Check whether the engine cylinder pressure is normal and whether there is air leakage. Clean the oil circuit, replace the spark plugs, filters, etc. Check whether the four wheels are dragging brakes.Check whether the quality of the oil is good. If not, replace the new oil.
2. Insufficient oil supply. The fuel system should be able to spray well-atomized fuel into the cylinder in a timely and appropriate amount. If the fuel system fails and the amount of oil in the injector cylinder is small, the heat generated by combustion is reduced. When the heat is reduced to the point that it cannot meet the requirements of the engine load, the engine is weak.
3. The reasons for Chaiwei's engine's boring hill climbing are as follows: excessive carbon accumulation: it is recommended to check whether the engine has accumulated too much carbon, which may generally lead to excessive carbon accumulation. Insufficient oil supply: The fuel system should be able to inject atomized fuel into the cylinder in a timely and appropriate manner.
1. Improper maintenance: The correct method is not mastered during maintenance, and low-purity gasoline or fuel oil is used, which will cause damage to the Weichai Guoliu natural gas egr valve. It is necessary to maintain the EGR valve regularly, clean up the accumulated carbon, and use gasoline and fuel additives with the correct label.
2. Engine jitter and lack of cylinder. Common reasons include spark plug ignition failure, ignition coil leakage, internal short circuit of the electric coil causing intermittent non-jump. The rust of the engine exhaust pipe causes the exhaust pipe to make a poof, and the exhaust gas is discharged from the middle without passing through the exhaust pipe, resulting in abnormal engine noise.
3. Simply put, the engine is an energy conversion mechanism, that is, the thermal energy of gasoline (diesel) is converted into mechanical energy through dense, which is the most basic principle of the engine.
4. Check whether there is too little fuel in the fuel tank and whether the pressure in the fuel pipe is unstable.
How to analyze global export trends
author: 2024-12-23 22:32Pharma supply chain mapping by HS code
author: 2024-12-23 22:14Dairy powder HS code references
author: 2024-12-23 21:57How to choose correct HS code in ASEAN
author: 2024-12-23 21:06HS code-based cargo insurance optimization
author: 2024-12-23 20:39How to find emerging export markets
author: 2024-12-23 22:10Agriculture trade by HS code in Africa
author: 2024-12-23 21:03Medical devices HS code mapping
author: 2024-12-23 20:34563.61MB
Check595.45MB
Check813.58MB
Check827.43MB
Check813.22MB
Check119.73MB
Check285.65MB
Check875.75MB
Check463.42MB
Check921.78MB
Check563.88MB
Check183.83MB
Check396.62MB
Check881.64MB
Check575.43MB
Check778.72MB
Check598.45MB
Check474.69MB
Check348.19MB
Check936.15MB
Check756.21MB
Check453.43MB
Check665.13MB
Check572.67MB
Check227.51MB
Check986.31MB
Check522.14MB
Check316.81MB
Check194.65MB
Check357.14MB
Check923.87MB
Check115.69MB
Check253.43MB
Check269.57MB
Check571.91MB
Check999.33MB
CheckScan to install
Industry-wise trade data breakdowns to discover more
Netizen comments More
1618 Forestry products HS code insights
2024-12-23 22:27 recommend
625 Pharmaceutical HS code compliance in India
2024-12-23 21:57 recommend
2654 Fish and seafood HS code mapping
2024-12-23 20:57 recommend
1838 Precision instruments HS code verification
2024-12-23 20:39 recommend
61 HS code filtering for import risk
2024-12-23 20:15 recommend