1. The closed-loop characteristic equation is 1+G(s) G(s) is the open-loop transfer function, Φ(s) is the closed-loop transfer function, so that the denominator = 0 is the closed-loop characteristic equation.
2. The closed-loop characteristic equation is 1+G(s) G(s) is the open-loop transfer function, Φ(s) is the closed-loop transfer function, so that the denominator = 0 is the closed-loop characteristic equation, and when the unit is fed back, h(s)=1. There are two types of open-loop transfer functions: the first one describes the dynamic characteristics of an open-loop system (a system without feedback).
3. The closed-loop characteristic equation is a polynomial equation whose root determines the stability and dynamic performance of the system. Specifically, the form of the closed-loop characteristic equation is 1+G(s) H(s)=0, where G(s) is the transfer function of the system and H(s) is the transfer function of the controller.
1. The closed-loop characteristic equation is: if the point on the s plane is a closed-loop pole, then the phase composed of zj and pi must satisfy the above two equations, and the modulus equation is related to Kg, while the phase angle equation is not related to Kg.
2. The closed-loop characteristic equation is 1+G(s). G(s) is an open-loop transfer function, Φ(s) is a closed-loop transfer function, and the denominator = 0 is a closed-loop characteristic equation.
3. The closed-loop characteristic equation is 1+G(s) G(s) is an open-loop transfer function, Φ(s) is a closed-loop transfer function, so that the denominator = 0 is a closed-loop characteristic equation. When the unit is fed back, h(s)=1. There are two types of open-loop transfer functions: the first one describes the dynamic characteristics of an open-loop system (a system without feedback).
4. If the open-loop transfer function GH=A/B, then fai=G/(1+GH), and the characteristic equation is 1+GH=0, that is, 1+A/B=0, that is, (A+B)/B=0, that is, A+B=0, that is, the intuitive numerator plus denominator.
Automatic control principle exercise (20 points) Try the structure diagram equivalently simplified to find the transfer function of the system shown in the figure below. Solution: So: II. ( 10 points) The characteristic equation of the known system is to judge the stability of the system. If the closed-loop system is unstable, point out the number of poles in the right half of the s plane.
According to the meaning of the question, the input signal is r(t)=4+6t+3t^2, the open-loop transfer function of the unit feedback system is G(s)=frac{ 8(0.5s+1)}{ s^2(0.1s+1)}. First of all, we need to convert the input signal r(t) into the Laplace transformation form.
The first question should be clear first. Since there is the same root trajectory, the open-loop functions of A and B must be the same, because the root trajectory is completely drawn according to the open-loop function. GHA=GHB=K(s+2)/s^2(s+4), I use GH to express the open loop, so as not to be confused with the latter.
This question involves the time domain method in modern control theory. 1 First, find the state transfer matrix. There are many methods. The following is solved by the Lasian inverse transformation method, which is more convenient: SI-A=[S-1 0;—1 S-1] Annotation: The matrix is represented by Matlab here, and the semicomon is used as a sign of two lines.
a, using the current relationship, the following relational formula can be obtained, ui/R1 =-uo/R2 -C duo/dt, and the Lashi transformation on both sides can obtain the relational formula in the question. B. You can use the superposition principle of the linear circuit to make u1 and u2 zero respectively, find the corresponding uo1 and uo2, and then add them to uo, and then do the Lashi transform.
HS code-based value chain optimization-APP, download it now, new users will receive a novice gift pack.
1. The closed-loop characteristic equation is 1+G(s) G(s) is the open-loop transfer function, Φ(s) is the closed-loop transfer function, so that the denominator = 0 is the closed-loop characteristic equation.
2. The closed-loop characteristic equation is 1+G(s) G(s) is the open-loop transfer function, Φ(s) is the closed-loop transfer function, so that the denominator = 0 is the closed-loop characteristic equation, and when the unit is fed back, h(s)=1. There are two types of open-loop transfer functions: the first one describes the dynamic characteristics of an open-loop system (a system without feedback).
3. The closed-loop characteristic equation is a polynomial equation whose root determines the stability and dynamic performance of the system. Specifically, the form of the closed-loop characteristic equation is 1+G(s) H(s)=0, where G(s) is the transfer function of the system and H(s) is the transfer function of the controller.
1. The closed-loop characteristic equation is: if the point on the s plane is a closed-loop pole, then the phase composed of zj and pi must satisfy the above two equations, and the modulus equation is related to Kg, while the phase angle equation is not related to Kg.
2. The closed-loop characteristic equation is 1+G(s). G(s) is an open-loop transfer function, Φ(s) is a closed-loop transfer function, and the denominator = 0 is a closed-loop characteristic equation.
3. The closed-loop characteristic equation is 1+G(s) G(s) is an open-loop transfer function, Φ(s) is a closed-loop transfer function, so that the denominator = 0 is a closed-loop characteristic equation. When the unit is fed back, h(s)=1. There are two types of open-loop transfer functions: the first one describes the dynamic characteristics of an open-loop system (a system without feedback).
4. If the open-loop transfer function GH=A/B, then fai=G/(1+GH), and the characteristic equation is 1+GH=0, that is, 1+A/B=0, that is, (A+B)/B=0, that is, A+B=0, that is, the intuitive numerator plus denominator.
Automatic control principle exercise (20 points) Try the structure diagram equivalently simplified to find the transfer function of the system shown in the figure below. Solution: So: II. ( 10 points) The characteristic equation of the known system is to judge the stability of the system. If the closed-loop system is unstable, point out the number of poles in the right half of the s plane.
According to the meaning of the question, the input signal is r(t)=4+6t+3t^2, the open-loop transfer function of the unit feedback system is G(s)=frac{ 8(0.5s+1)}{ s^2(0.1s+1)}. First of all, we need to convert the input signal r(t) into the Laplace transformation form.
The first question should be clear first. Since there is the same root trajectory, the open-loop functions of A and B must be the same, because the root trajectory is completely drawn according to the open-loop function. GHA=GHB=K(s+2)/s^2(s+4), I use GH to express the open loop, so as not to be confused with the latter.
This question involves the time domain method in modern control theory. 1 First, find the state transfer matrix. There are many methods. The following is solved by the Lasian inverse transformation method, which is more convenient: SI-A=[S-1 0;—1 S-1] Annotation: The matrix is represented by Matlab here, and the semicomon is used as a sign of two lines.
a, using the current relationship, the following relational formula can be obtained, ui/R1 =-uo/R2 -C duo/dt, and the Lashi transformation on both sides can obtain the relational formula in the question. B. You can use the superposition principle of the linear circuit to make u1 and u2 zero respectively, find the corresponding uo1 and uo2, and then add them to uo, and then do the Lashi transform.
Dynamic supplier inventory analysis
author: 2024-12-23 23:03How to access protected trade databases
author: 2024-12-23 22:54HS code alignment with labeling standards
author: 2024-12-23 20:57HS code adaptation for local regulations
author: 2024-12-23 20:55HS code-driven customs clearance SLAs
author: 2024-12-23 20:29Understanding HS codes in trade data
author: 2024-12-23 22:53HS code-based value chain optimization
author: 2024-12-23 22:52How to find compliant suppliers
author: 2024-12-23 22:24HS code-based scenario planning for exports
author: 2024-12-23 20:43333.26MB
Check918.41MB
Check568.88MB
Check289.35MB
Check898.54MB
Check531.73MB
Check791.61MB
Check934.15MB
Check199.85MB
Check921.85MB
Check595.82MB
Check872.45MB
Check658.22MB
Check858.82MB
Check282.24MB
Check816.87MB
Check589.29MB
Check512.98MB
Check956.34MB
Check372.68MB
Check583.16MB
Check516.79MB
Check698.55MB
Check937.71MB
Check426.68MB
Check537.69MB
Check317.36MB
Check192.59MB
Check355.88MB
Check713.98MB
Check357.31MB
Check132.59MB
Check293.45MB
Check442.63MB
Check822.33MB
Check976.38MB
CheckScan to install
HS code-based value chain optimization to discover more
Netizen comments More
1742 Pharmaceutical compliance monitoring
2024-12-23 22:36 recommend
690 Real-time trade data feeds
2024-12-23 22:12 recommend
1548 HS code-based compliance checks for EU
2024-12-23 21:48 recommend
851 Industrial spare parts HS code mapping
2024-12-23 21:30 recommend
1723 Real-time cargo insurance insights
2024-12-23 20:44 recommend