Connect the new hard disk to the computer; download and install the partition assistant (free software); start the partition assistant program, (1) click the system disk of the original hard disk, (2) click [migrate system to firmware] on the left side of the window State drive], (3) Click: Next in the open window.
When booting, there is a prompt in the lower right corner of the screen. Now the new motherboard does not need to enter the BIOS to set the computer to start from the CD-ROM. For example, the Gigabyte motherboard can be turned on and press F12 to choose to start from the CD-ROM.
Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk. If you are the old masterBoard, it will take a little effort. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
1. Use GPT partition mode to partition 3TB hard disk: open DiskGenius tool, first click to select the 3T hard disk, then click "Quick Partition" at the top, and then remember to select the GPT format (GUID) in the partition table type as shown in the figure below.
2. Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk.If you are an old motherboard, you will have to work harder. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
3. The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area. Then use GHOST to restore to the system partition, and then repair the boot to start the system.
4. In the figure, the 3T hard disk is used as a system disk (the hard disk that installs the operating system). 2: When the hard disk larger than 2T is used as a system disk, when the bios is booted to Legacy (traditional boot) and the partition mode is MBR, the MBR partition cannot manage a capacity of more than 2T, and can only be idle.
1. Maybe your hard disk boot area Problem, or there is a problem with the system. Plug in the cable inside the machine, (including hard disk, optical drive power supply and data cable) board card, wipe off the golden finger of the card, and clear the dust. Enter COMS to restore the factory settings.
2. If the system can be installed, then there is no problem with the hardware, so either it is a problem with the installation of the operating system or the BIOS settings do not match the system.
3. The system boot sector is lost. Solution: Insert the PE boot disk to enterPE desktop, use partition software to rebuild mbr, and then use system boot repair software to rebuild system boot. The hard disk is loose, the interface is closed for some reason or the startup item of the hard disk is deleted, resulting in the device not being recognized.
1. The speed of the monitoring dedicated hard disk is much slower than that of the computer, and it cannot be used as a system disk. If it is no problem at all as a warehouse disk, it will not have any impact on the computer. It's just that the monitoring hard disk is slow and slow when reading data.
2. If the removed monitoring hard disk is added to the ordinary desktop, it cannot be recognized, because the ordinary desktop cannot load the system of this hard disk.
3. This can be calculated. It depends on how high the bit rate you set the DVR video. Generally, the maximum video effect of DVR is 512K, and you can choose it yourself, 64K, 128K, 256K, etc. There are also miscellaneous DVRs that cannot be selected, generally 128K.
4. Finally, it can be used! Method 3: Install the system (take the installation of WINDOWS XP as an example below) I chose a complete Windows XP installation CD without any cracks.
5. The monitored hard disk is also a conventional mechanical hard disk. It can be used directly, just use the previous partition format. If you want to use the main disk, you need to install an operating system.
6, Configuration--SATIn A-Operation, you can see that the hard disk mode is RAID On. After selecting the AHCI mode and pressing F10 to save and restart, the 3T large hard disk can be recognized normally. It is recommended to use diskgenius software to split the disk, and the Disk management that comes with Windows may not be fully allocated.
1. The system image file is damaged: If there is a problem with your image file, an error will be prompted in the process of copying the image file, and the system cannot be installed. You need to re-download the mirror image (ISO) file.
2. There are two main reasons why the hard disk cannot install the operating system: hard disk problems and setting problems. The problems of the hard disk include the wrong partition format, the hard disk cannot be recognized by the motherboard, and the hard disk itself is damaged. THE SETTING PROBLEMS ARE MAINLY THE SETTINGS OF SATA MODE (USUALLY IN ACHI MODE, THE WIN XP SYSTEM CANNOT BE INSTALLED OR USED) AND THE HARD DISK ERROR SELECTED DURING INSTALLATION.
3. The old motherboard BIOS does not support UEFI startup. You have to consider getting a hard disk installation system of less than 2TB to start.If you want the old motherboard to support 3TB hard disk startup, the operation is very complicated and may not be successful. To be honest, it is better to use a hard disk within 2T as a system disk, which is more practical.
win7 must use the 64-bit version and integrate the UEFI module.
The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area.Then use GHOST to restore to the system partition, and then repair the boot to start the system.
Install the system win7: Preparation: 1 Make a USB boot disk.
Win7 64-bit system can support reading and writing of GPT disk and booting from GPT disk with the support of UEFI. You can use Diskgenius or Partition Assistant to establish the disk as a GPT partition table disk and then partition it. There is no logical partition on the GPT disk, and all of them are the main partition.
No, it usually needs to be installed with auxiliary tools. Because the system mirror file itself cannot be run. You can reinstall the win7 system with a USB flash drive: make a boot disk.
Global logistics analytics platforms-APP, download it now, new users will receive a novice gift pack.
Connect the new hard disk to the computer; download and install the partition assistant (free software); start the partition assistant program, (1) click the system disk of the original hard disk, (2) click [migrate system to firmware] on the left side of the window State drive], (3) Click: Next in the open window.
When booting, there is a prompt in the lower right corner of the screen. Now the new motherboard does not need to enter the BIOS to set the computer to start from the CD-ROM. For example, the Gigabyte motherboard can be turned on and press F12 to choose to start from the CD-ROM.
Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk. If you are the old masterBoard, it will take a little effort. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
1. Use GPT partition mode to partition 3TB hard disk: open DiskGenius tool, first click to select the 3T hard disk, then click "Quick Partition" at the top, and then remember to select the GPT format (GUID) in the partition table type as shown in the figure below.
2. Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk.If you are an old motherboard, you will have to work harder. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
3. The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area. Then use GHOST to restore to the system partition, and then repair the boot to start the system.
4. In the figure, the 3T hard disk is used as a system disk (the hard disk that installs the operating system). 2: When the hard disk larger than 2T is used as a system disk, when the bios is booted to Legacy (traditional boot) and the partition mode is MBR, the MBR partition cannot manage a capacity of more than 2T, and can only be idle.
1. Maybe your hard disk boot area Problem, or there is a problem with the system. Plug in the cable inside the machine, (including hard disk, optical drive power supply and data cable) board card, wipe off the golden finger of the card, and clear the dust. Enter COMS to restore the factory settings.
2. If the system can be installed, then there is no problem with the hardware, so either it is a problem with the installation of the operating system or the BIOS settings do not match the system.
3. The system boot sector is lost. Solution: Insert the PE boot disk to enterPE desktop, use partition software to rebuild mbr, and then use system boot repair software to rebuild system boot. The hard disk is loose, the interface is closed for some reason or the startup item of the hard disk is deleted, resulting in the device not being recognized.
1. The speed of the monitoring dedicated hard disk is much slower than that of the computer, and it cannot be used as a system disk. If it is no problem at all as a warehouse disk, it will not have any impact on the computer. It's just that the monitoring hard disk is slow and slow when reading data.
2. If the removed monitoring hard disk is added to the ordinary desktop, it cannot be recognized, because the ordinary desktop cannot load the system of this hard disk.
3. This can be calculated. It depends on how high the bit rate you set the DVR video. Generally, the maximum video effect of DVR is 512K, and you can choose it yourself, 64K, 128K, 256K, etc. There are also miscellaneous DVRs that cannot be selected, generally 128K.
4. Finally, it can be used! Method 3: Install the system (take the installation of WINDOWS XP as an example below) I chose a complete Windows XP installation CD without any cracks.
5. The monitored hard disk is also a conventional mechanical hard disk. It can be used directly, just use the previous partition format. If you want to use the main disk, you need to install an operating system.
6, Configuration--SATIn A-Operation, you can see that the hard disk mode is RAID On. After selecting the AHCI mode and pressing F10 to save and restart, the 3T large hard disk can be recognized normally. It is recommended to use diskgenius software to split the disk, and the Disk management that comes with Windows may not be fully allocated.
1. The system image file is damaged: If there is a problem with your image file, an error will be prompted in the process of copying the image file, and the system cannot be installed. You need to re-download the mirror image (ISO) file.
2. There are two main reasons why the hard disk cannot install the operating system: hard disk problems and setting problems. The problems of the hard disk include the wrong partition format, the hard disk cannot be recognized by the motherboard, and the hard disk itself is damaged. THE SETTING PROBLEMS ARE MAINLY THE SETTINGS OF SATA MODE (USUALLY IN ACHI MODE, THE WIN XP SYSTEM CANNOT BE INSTALLED OR USED) AND THE HARD DISK ERROR SELECTED DURING INSTALLATION.
3. The old motherboard BIOS does not support UEFI startup. You have to consider getting a hard disk installation system of less than 2TB to start.If you want the old motherboard to support 3TB hard disk startup, the operation is very complicated and may not be successful. To be honest, it is better to use a hard disk within 2T as a system disk, which is more practical.
win7 must use the 64-bit version and integrate the UEFI module.
The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area.Then use GHOST to restore to the system partition, and then repair the boot to start the system.
Install the system win7: Preparation: 1 Make a USB boot disk.
Win7 64-bit system can support reading and writing of GPT disk and booting from GPT disk with the support of UEFI. You can use Diskgenius or Partition Assistant to establish the disk as a GPT partition table disk and then partition it. There is no logical partition on the GPT disk, and all of them are the main partition.
No, it usually needs to be installed with auxiliary tools. Because the system mirror file itself cannot be run. You can reinstall the win7 system with a USB flash drive: make a boot disk.
Comparative trade route analysis
author: 2024-12-23 22:26Commodity-specific import licensing data
author: 2024-12-23 21:32Trade data-driven logistics planning
author: 2024-12-23 20:55European Union trade analytics
author: 2024-12-23 20:53Global supply chain partner networks
author: 2024-12-23 23:00Industry-specific tariff code reference
author: 2024-12-23 22:52How to monitor competitor supply chains
author: 2024-12-23 21:56Global HS code standardization efforts
author: 2024-12-23 21:28Global trade e-commerce insights
author: 2024-12-23 20:43884.26MB
Check314.86MB
Check378.76MB
Check627.87MB
Check521.73MB
Check572.93MB
Check389.68MB
Check346.85MB
Check383.26MB
Check711.27MB
Check395.17MB
Check715.12MB
Check443.98MB
Check536.22MB
Check779.92MB
Check565.77MB
Check375.46MB
Check941.79MB
Check498.28MB
Check321.28MB
Check581.83MB
Check767.51MB
Check458.55MB
Check955.54MB
Check218.99MB
Check321.29MB
Check671.68MB
Check195.79MB
Check952.74MB
Check574.72MB
Check499.93MB
Check618.14MB
Check533.47MB
Check269.33MB
Check819.54MB
Check391.36MB
CheckScan to install
Global logistics analytics platforms to discover more
Netizen comments More
421 HS code-driven compliance workflows
2024-12-23 23:14 recommend
600 Data-driven trade procurement cycles
2024-12-23 22:15 recommend
2561 High-value electronics HS code checks
2024-12-23 21:39 recommend
2923 HS code-based market share analysis
2024-12-23 21:34 recommend
1042 How to access niche export markets
2024-12-23 21:03 recommend